Skullcandy Sesh Left Earbud Not Turning On (Solved)

I have a fondness for my Skullcandy Sesh earbuds due to their excellent sound performance. Up until recently, I hadn’t encountered any problems with them. However, just yesterday, I experienced a malfunction where the left earbud failed to power on, and additionally, I was unable to pair the two earbuds.

This issue didn’t amount to much, as I managed to repair my earbud by consulting discussions on internet forums and viewing some instructional videos.

If your left Skullcandy Sesh earbud won’t power on, don’t worry. Stick around because I’ll share several methods to solve this issue.

How to Resolve an Issue with the Left Earbud of Skullcandy Sesh Not Powering Up?

Keep in mind that these remedies will be effective only if your Skullcandy Sesh earbuds haven’t sustained any physical harm.

 Reset Skullcandy Indy 

At times, your earbuds might fail to power up due to errors or issues in the software. When this happens, it’s necessary to reset your earbuds.

Thus, it is advised that you perform a reset on your Skullcandy Sesh earbuds.

To reset your Skullcandy Sesh earbuds, please adhere to the subsequent instructions.

• Take both earpieces out of their charging container.
• Proceed to deactivate them by holding your touch on the earbuds for a duration of four seconds.
• Hold down on both earbuds for 10 seconds after they have been powered off.
• After that, the earbuds will reset.

 Charge Left Earbud 

The next step is to power up the left earpiece. It’s possible that a depleted battery is the reason it isn’t activating.

Therefore, it is advised to keep it in the charging case for a minimum of one hour for charging.

Ensure that the earbud begins charging once you have placed it in its case.

Discover why your earbuds may not be powering up and learn what steps you can take to address this issue.

Why isn’t the Left Earbud Charging?

If there’s a buildup of grime on the charging contacts of the left earbud or the corresponding connectors inside the charging case, the earbud won’t power up. Therefore, it’s important to regularly clean both the earbud’s contacts and the pins on the left compartment of the case.

To clean, toothpicks and isopropyl alcohol are effective tools. Just apply a small amount of the alcohol to the toothpick and gently scrub the charging connectors and pins.

Ensure that both items are completely dry after cleaning them, prior to plugging them in for charging.

Additionally, ensure that the ear tips for the left earbud are properly attached. Improperly fitted ear tips can prevent the earbud from properly seating in the charging case, leading to charging issues.

Lastly, gently press down on the earbud when placing it into the case.

 Update Firmware 

Another potential cause for your earbud not powering on could be obsolete software. So, it’s recommended to install the latest updates for your Skullcandy Sesh earbuds.

The software upgrade will resolve small issues and enhance the functioning of your earbuds.

Here are the instructions to upgrade the firmware on your Skullcandy Sesh earbuds.

• Acquire and set up the Skullcandy application onto your gadget.
• Pair the earbuds with your device first, and then establish a connection with the app.
• Open the Skullcandy app.
• Navigate to the notification section to check if an update is accessible there.
• Should there be an update ready, press on ‘download’ and proceed to install said update.

Nonetheless, should a firmware update be unsuccessful, it’s essential to make sure of the following points.

• Ensure that the battery level of the earbuds is a minimum of 25 percent. Should it fall below that threshold, proceed to recharge them.
• Make sure your internet connection is reliable.
• Should the charge level of the cell phone battery drop below 30%, it is advisable to connect it to a power source to recharge.
• Ensure that your earbuds are paired with both your smartphone and the application.

Once you’ve fulfilled these prerequisites, reopen the application and proceed to upgrade the firmware.

 Drain Battery 

Perhaps the reason your earbud won’t power up is because of some technical issues. In order to fix these problems, it’s advisable to completely deplete the battery in the earbuds.

To accomplish this task, adhere to the steps outlined below.

• Begin by disconnecting the earbuds from any devices they are currently paired with.
• Turn off the Bluetooth of your device.
• Remove earbuds from the charging case.
• Stay away from the situation for 12 to 24 hours.
• Next, insert the earbuds into the case and allow them to charge for a duration of one hour.

With any luck, once the battery has been completely depleted, the technical issues with your Skullcandy Sesh earbuds should be resolved, allowing them to power up again.

 Replace Battery 

The earbuds rely solely on the battery for energy. Should none of the suggested solutions succeed in activating your Skullcandy Sesh, this indicates that the battery within the earbuds is broken.

And you need to replace it.

It’s advisable to reach out to a skilled technician who specializes in electronics for the purpose of exchanging the battery, as they will be able to accomplish the job with ease.

 Contact Skullcandy 

You might consider reaching out to Skullcandy’s customer service for assistance as a final step. However, when I got in touch with them, they simply provided me with the same elementary troubleshooting steps that we’ve previously gone over.

Following that, they will request some details regarding your earbuds to proceed with the exchange.

Typically, if you bought your earbuds less than a year ago, you have the option to return them.

Therefore, if all attempts at repairing your earbuds are unsuccessful, my advice would be to send them back.

Why isn’t the left earbud of the Sesh model functioning?

The issue with the left Skullcandy Sesh earbud might stem from a nearly depleted battery, a faulty battery, or some errors within the software.

To repair the earbud, ensure it is fully charged by plugging it in for several hours, conduct a reset, install any firmware updates, and verify that the charging mechanism is functioning properly.

How do I activate the left earpiece of my Skullcandy headphones?

Usually, when you take out the earbud from its container, it automatically powers up. But if it fails to switch on by itself, you have the option to activate it by hand.

To activate the left earbud from Skullcandy by hand, press and hold it for over four seconds. After this time has passed, the earbud will power up.

 Conclusion 

The content of this piece provided solutions for resolving issues with the left earbud of the Skullcandy Sesh failing to power on. It is desired that the suggested solutions will restore your earbuds to their proper functioning state. We invite you to share your thoughts on this post in the comment section and encourage you to return for additional insights regarding headphones.